QUESTION 201
Which three statements about VTP features are true? (Choose three.)
A. VTP works at Layer 3 of the OSI model and requires that a management VLAN IP address be configured.
B. When properly configured, VTP minimizes VLAN misconfigurations and configuration inconsistencies.
C. When properly configured, VTP maintains VLAN configuration consistency and accelerates trunk link negotiation.
D. Each broadcast domain on a switch can have its own unique VTP domain.
E. VTP pruning is used to increase available bandwidth in trunk links.
F. To configure a switch to be part of two VTP domains, each domain must have its own passwords.
G. Client, server, and transparent are valid VTP modes.
Correct Answer: BEG
QUESTION 202
Two switches are connected through a trunk link. Which two commands show that there is a native VLAN mismatch on that link? (Choose two.)
A. show vlan brief
B. show interface trunk
C. show interface vlan
D. show interface switchport
E. show interface interface
F. show switchport trunk
Correct Answer: BD
QUESTION 203
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC
QUESTION 204
Which statement about IPv6 is true?
A. Addresses are not hierarchical and are assigned at random.
B. Only one IPv6 address can exist on a given interface.
C. There are 2.7 billion addresses available.
D. Broadcasts have been eliminated and replaced with multicasts.
Correct Answer: D
QUESTION 205
Refer to the exhibit. The user at Workstation B reports that Server A cannot be reached. What is preventing Workstation B from reaching Server A?
A. The IP address for Server A is a broadcast address.
B. The IP address for Workstation B is a subnet address.
C. The gateway for Workstation B is not on the same subnet.
D. The gateway for Server A is not on the same subnet.
Correct Answer: D
QUESTION 206
You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the maximum number of subnets. Which network address and subnet mask meet this requirement?
A. 192.168.252.0 255.255.255.252
B. 192.168.252.8 255.255.255.248
C. 192.168.252.8 255.255.255.252
D. 192.168.252.16 255.255.255.240
E. 192.168.252.16 255.255.255.252
Correct Answer: B
QUESTION 207
Refer to the exhibit. Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?
A. The router will forward packets from R3 to R2 to R1.
B. The router will forward packets from R3 to R1 to R2.
C. The router will forward packets from R3 to R2 to R1 AND from R3 to R1.
D. The router will forward packets from R3 to R1.
Correct Answer: C
QUESTION 208
How does using the service password-encryption command on a router provide additional security?
A. by encrypting all passwords passing through the router
B. by encrypting passwords in the plain text configuration file
C. by requiring entry of encrypted passwords for access to the device
D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges
E. by automatically suggesting encrypted passwords for use in configuring the router
Correct Answer: B
QUESTION 209
Refer to the exhibit. How will the router handle a packet destined for 192.0.2.156?
A. The router will drop the packet.
B. The router will return the packet to its source.
C. The router will forward the packet via Serial2.
D. The router will forward the packet via either Serial0 or Serial1.
Correct Answer: C
QUESTION 210
Refer to the exhibit. The show interfaces serial 0/1 command was issued on the R10-1 router. What can be concluded from the output in the exhibit?
A. The cable connected to the serial 0/1 interface of the R10-1 router is a DTE cable.
B. The R10-1 router can ping the router interface connected to the serial 0/1 interface.
C. The clock rate used for interface serial 0/1 of the R10-1 router is 1,544,000 bits per second.
D. The CSU used with the serial 0/1 interface of the R10-1 router has lost connection to the service provider.
E. The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is using the default serial interface encapsulation.
Correct Answer: E
Download Latest Cisco 200-101 ICND2 Real Free Tests , help you to pass exam 100%.
